Go Back   Two Wheel Fix > General > Cage Hell > Cage Tech

Reply
 
Thread Tools Display Modes
Old 08-28-2009, 09:36 PM   #1
BobTheBiker
too much time on my hands
 
BobTheBiker's Avatar
 
Join Date: Jul 2008
Location: the northern district of god damn
Moto: 01 ZX6R, looking for more now.
Posts: 1,802
Default 96 S10 fuel issue

Anyone have some ideas here?

I've got a 96 S10 2.2, everyting is wired up right, and hooked up where its supposed to be, but I cant get the truck to run because the fuel injectors arent firing as they need to be. I've got ONE plug I cant figure out, looks just like the cam position sensor plug, but the notch is different and theres nowhere for it to go on my motor.

Right now, the truck runs with ether in the intake, but wont start on its own. I'm not really sure WTF to make of it, but its annoying as shit.

anyone got some input? My only idea now is ECU is toast.
BobTheBiker is offline   Reply With Quote
Old 08-29-2009, 01:52 AM   #2
101lifts2
WSB Champion
 
101lifts2's Avatar
 
Join Date: Nov 2008
Location: Anaheim, CA
Moto: 2009 Kawi ZX6R
Posts: 5,570
Default

Quote:
Originally Posted by BobTheBiker View Post
Anyone have some ideas here?

I've got a 96 S10 2.2, everyting is wired up right, and hooked up where its supposed to be, but I cant get the truck to run because the fuel injectors arent firing as they need to be. I've got ONE plug I cant figure out, looks just like the cam position sensor plug, but the notch is different and theres nowhere for it to go on my motor.

Right now, the truck runs with ether in the intake, but wont start on its own. I'm not really sure WTF to make of it, but its annoying as shit.

anyone got some input? My only idea now is ECU is toast.
If the vehicle runs off of ether, then the CAM and CRANK signals are ok or at least enough to run the engine.

Does the fuel pump energize with the key initially turned ON?

Check the ECM IGN 20A fuse that supplies ignition voltages to all 4 fuel injectors. Then make sure there is 12V at each fuel injector with the key on, engine off.

If you can get ahold of a noid light, you can plug it into one of the fuel injector connectors and crank over the engine. If the noid light blinks, you probably have a fuel delivery/regulator/fuel issue.

The ECM BATT 20A fuse feeds the fuel pump relay, but the the fuel pump will run w/o the relay if oil pressure is present (bypass).
__________________
Train Hard

Ron Paul - 2012

Mark of Excellence
GM
101lifts2 is offline   Reply With Quote
Old 08-29-2009, 01:59 AM   #3
BobTheBiker
too much time on my hands
 
BobTheBiker's Avatar
 
Join Date: Jul 2008
Location: the northern district of god damn
Moto: 01 ZX6R, looking for more now.
Posts: 1,802
Default

I was looking at it more earlier and the issue dawned on me. I had the wrong fucking crank sensor in there. people keep saying how the crank sensor is behind the motor mount, but never mention a wire going to the coil off it, so I had to go swap with the one off my original block, along with the original coils.
BAM! problem seems to no longer be a problem, and all but 3 plugs(former AC system and one evap unit) now have homes. I'll test better in the AM since I'm in an apartment complex and theres little kids livin next to where I work on my truck. dont need angry neighbors.
BobTheBiker is offline   Reply With Quote
Old 08-29-2009, 08:43 PM   #4
101lifts2
WSB Champion
 
101lifts2's Avatar
 
Join Date: Nov 2008
Location: Anaheim, CA
Moto: 2009 Kawi ZX6R
Posts: 5,570
Default

How are we supposed to fix ur shit when you have the incorrect parts installed. Hit urself in the head!
__________________
Train Hard

Ron Paul - 2012

Mark of Excellence
GM
101lifts2 is offline   Reply With Quote
Old 08-30-2009, 06:09 AM   #5
BobTheBiker
too much time on my hands
 
BobTheBiker's Avatar
 
Join Date: Jul 2008
Location: the northern district of god damn
Moto: 01 ZX6R, looking for more now.
Posts: 1,802
Default

that was a TOTAL brainfart. I done more than hit myself. I went and drank myself dumb a few hours ago as punishment. who are you again?
BobTheBiker is offline   Reply With Quote
Old 08-31-2009, 12:31 AM   #6
101lifts2
WSB Champion
 
101lifts2's Avatar
 
Join Date: Nov 2008
Location: Anaheim, CA
Moto: 2009 Kawi ZX6R
Posts: 5,570
Default

The master of all automotive.
__________________
Train Hard

Ron Paul - 2012

Mark of Excellence
GM
101lifts2 is offline   Reply With Quote
Old 08-31-2009, 02:49 AM   #7
BobTheBiker
too much time on my hands
 
BobTheBiker's Avatar
 
Join Date: Jul 2008
Location: the northern district of god damn
Moto: 01 ZX6R, looking for more now.
Posts: 1,802
Default

You cant be the master of all automotive. I know that guy. his name was jesus and he has a beard.

anyways, the fuel issue is sorted, but now when I rev it, its got a nasty rattle from somewhere. I'm inclined to say the belt tensioner because the belt on it is obscenely small and puttin a good deal of strain on the tensioner. plus a portion of my belt actually got shredded today as I watched. glad my fingers werent in the way.

this noise only happens briefly then disappears, and only happens on quick acceleration of the motor's rpms. doesnt sound like a constant rattle from top or bottom end like a bearing going out.
BobTheBiker is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:46 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.