Attn Ladies - do you do your own maintenance? - Page 6

Gas Man · 07-09-2010, 12:05 PM

Quote:

Originally Posted by marko138

No, if I had the money I'd pay.

Isn't that how it always is for most of us!!!

z06boy · 07-09-2010, 12:38 PM

Just bought 8 NGK CR9EK plugs for the bikes...$47 shipped to the house...guess that's about as good as I was going to find.

Now looking for a decent deal on two air filters.

I do all of the maintenance on the vehicles...3 cars...two bikes and a boat and the wife handles mucho other stuff around the house.

I did show her how to clean and lube the chain on her bike a while back.

gavilan · 07-09-2010, 05:03 PM

I have the carb block of a 93 Nighthawk that I pulled off a couple of months ago because I was going to tear it apart, clean the carbs and rebuild the thing...

Darn block was sitting in my office for a few weeks, traveling in my car everywhere with me for a couple more, went back to the office (we have a lab with a bunch of tools I thought I could use), back to the car and now it's been sitting in my garage at home for... a while.

I SO have to get to it but what originally discouraged me was that I stripped a couple of screws, ran to get a tapping set and got out most of them, but two screws ended up with pieces of taps in them, still pretty much attached to the block -thankyouverymuch.

I know it's not going to be a big deal once I finally sit down and do it but it's just gotten to the point where I am just *dreading* it.

This weekend... I am sure... well... we'll see... lol

Of course, after I am done with that, the question will be whether after all this time I actually remember how to put them back and attach everything else, but I guess I'll solve that issue when I get to it

(I did take some pictures of some things that I took apart and thought 'uh-oh, looks complicated...'

)

Ah... the joy of working on an old(er) bike...

racedoll · 07-09-2010, 06:10 PM

Quote:

Originally Posted by z06boy

Just bought 8 NGK CR9EK plugs for the bikes...$47 shipped to the house...guess that's about as good as I was going to find.

I think I have 4 of those brand new in a drawer in the garage that I can't use.

Rangerscott · 07-09-2010, 08:27 PM

Quote:

Originally Posted by racedoll

I think I have 4 of those brand new in a drawer in the garage that I can't use.

Copper or Iridium tip?

racedoll · 07-09-2010, 10:20 PM

Quote:

Originally Posted by Rangerscott

Copper or Iridium tip?

They are just the standard tip. - http://www.ngksparkplugs.com/part_fi...=1690&type=reg

And I'll change my avatar since you seem to be offended.

Amber Lamps · 07-09-2010, 10:21 PM

Quote:

Originally Posted by racedoll

They are just the standard tip.

And I'll change my avatar since you seem to be offended.

More like jealous!!!

BA-ZING!!!

Rangerscott · 07-09-2010, 10:58 PM

Hey hey. Rules are rules. No Cooter flashing allowed.

So just the tip huh. Sounds like a fun game.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-09-2010, 12:38 PM	#52
z06boy Letzroll Join Date: Feb 2008 Location: Lake Norman area, NC Moto: 07 Red R1 & 07 Blue R6 Posts: 5,265	Just bought 8 NGK CR9EK plugs for the bikes...$47 shipped to the house...guess that's about as good as I was going to find. Now looking for a decent deal on two air filters. I do all of the maintenance on the vehicles...3 cars...two bikes and a boat and the wife handles mucho other stuff around the house. I did show her how to clean and lube the chain on her bike a while back.

07-09-2010, 05:03 PM	#53
gavilan Street Stunter Join Date: May 2010 Location: San Diego, CA Posts: 71	I have the carb block of a 93 Nighthawk that I pulled off a couple of months ago because I was going to tear it apart, clean the carbs and rebuild the thing... Darn block was sitting in my office for a few weeks, traveling in my car everywhere with me for a couple more, went back to the office (we have a lab with a bunch of tools I thought I could use), back to the car and now it's been sitting in my garage at home for... a while. I SO have to get to it but what originally discouraged me was that I stripped a couple of screws, ran to get a tapping set and got out most of them, but two screws ended up with pieces of taps in them, still pretty much attached to the block -thankyouverymuch. I know it's not going to be a big deal once I finally sit down and do it but it's just gotten to the point where I am just dreading it. This weekend... I am sure... well... we'll see... lol Of course, after I am done with that, the question will be whether after all this time I actually remember how to put them back and attach everything else, but I guess I'll solve that issue when I get to it (I did take some pictures of some things that I took apart and thought 'uh-oh, looks complicated...' ) Ah... the joy of working on an old(er) bike...

07-09-2010, 10:58 PM	#58
Rangerscott Viff6N Mutated Warrior Join Date: Mar 2009 Location: Texas Moto: '01 Honda VFR 800 & '09 ER-6N Posts: 8,704	Hey hey. Rules are rules. No Cooter flashing allowed. So just the tip huh. Sounds like a fun game.